 |  |  |  |
POR-Strip
DIRECTIONS AND CAUTIONS
Remove all plastic materials and other items such as lenses, moldings,
windshield wipers, grills, mirrors, chrome, etc. When stripping door jams,
remove soft rubber or cover it with masking tape before spraying. Wear
rubber gloves and protective clothing at all times. When stripping an entire
automobile or boat, begin high and do small sections at a time. Work in a
well-ventilated area where temperature is above 50 F (10OC) degrees and
below 95 F (35OC) degrees. Do not work in direct sunlight or under windy
conditions. Surface to be stripped should be cool, not hot. An open garage will
provide the best working conditions.
Contains Methylene Chloride. May irritate skin. Contact with flame or hot
surface may produce toxic gases.
APPLICATION PROCEDURE SHAKE WELL BEFORE USING
1. Spray on a full wet coat, but avoid running or dripping. Let it set for 15
minutes if surface was enamel, or 5 minutes if surface was lacquer.
2. Apply a second coat over the first and permit to set for another 15
minutes (enamel surface). For lacquer finishes, move to step 3.
3. Remove the stripped finish using a plastic spreader or other suitable
tool. Re-spray surface with stripper and wash, using steel wool and
water to final clean the surface. Wash from the bottom up on each panel.
Use water only, as soap may leave a residue or film.
POR-15 Paint Remover/Stripper will NOT damage the following:
Glass, Duct Tape, Wood, Glue, Veneer, Rubber*, Leather**, Brass, Steel, Plaster
Walls, Wicker, Aluminum, Factory Fiberglass.
POR-15 Paint Remover/Stripper Will DAMAGE or remove the following:
Tile, Linoleum, Asphalt, Plastics, Synthetics, Sheet Rock, Paper Wicker, Bondo
& other body fillers, when Stripping..Imron, apply two full coats, waiting 10
minutes between coats.GM Black Primer, remove topcoat first, then spray one
full coat, wait 5-10 minutes, then wash with #2 steel wool and water.
Baked Enamel, spray one full wet coat, wait 10 minutes and spray a second
coat over the fi rst without removing any paint. Wait 10 minutes and remove
with scraper. Lacquer, spray a full wet coat, wait 5-10 minutes and lacquer will
melt off. Use plastic scraper to remove.
Polyurethane, spray a full wet coat, wait 20 minutes and remove. POR-15 Paint
Remover/Stripper must be neutralized with a water rinse on metal after
stripped paint has been removed...will not raise the grain on stripped wood...is
not harmed by freezing...will remove mild surface rust...does not contain lye or
acid.
When stripping wood: wash off stripper with wood alcohol, denatured alcohol,
or methanol.
Shelf Life is up to 6 months in an unopened bottle, but it is recommended
that product be used as soon as possible after purchase.
* If rubber soaks in stripper for an hour or more it may temporarily lose its shape; however, if
subsequently washed with water and permitted to dry it will return to original shape.
** Stripper will remove natural oils from leather, but these can easily be replaced with leather
lubricants, tung oil, saddle soap, hide food or other similar products.
CAUTIONS: Keep away from heat, sparks, or open fl ame. Keep container
closed when not in use. Do not take internally. Contact with flame or hot
surface may produce toxic gases. Use of goggles and gloves is strongly
recommended to avoid skin contact or accidental contact. Store away from
heat and out of direct sunlight. Open can slowly to release pressure. If skin
contact is made, wash immediately with soap and water. Avoid prolonged
breathing of vapors. Use only with adequate ventilation. Persons with known
respiratory or heart ailments should exercise extreme caution when using
Methylene-Chloride based products.
Avoid exposure to fumes or vapors.
KEEP OUT OF THE REACH OF CHILDREN
FIRST AID: If swallowed, call physician, hospital emergency room or poison
control center immediately for instructions on inducing vomiting. DO NOT USE
table salt solution. If possible, give one tablespoon of Ipecac syrup and one
glass of water. Patient should lie down, keep warm, cover eyes to exclude light.
FOR EYE CONTACT: Flush repeatedly with water.
FOR SKIN BURN: Apply petroleum jelly to skin.
DIRECTIONS AND CAUTIONS
Remove all plastic materials and other items such as lenses, moldings,
windshield wipers, grills, mirrors, chrome, etc. When stripping door jams,
remove soft rubber or cover it with masking tape before spraying. Wear
rubber gloves and protective clothing at all times. When stripping an entire
automobile or boat, begin high and do small sections at a time. Work in a
well-ventilated area where temperature is above 50 F (10OC) degrees and
below 95 F (35OC) degrees. Do not work in direct sunlight or under windy
conditions. Surface to be stripped should be cool, not hot. An open garage will
provide the best working conditions.
Contains Methylene Chloride. May irritate skin. Contact with flame or hot
surface may produce toxic gases.
APPLICATION PROCEDURE SHAKE WELL BEFORE USING
1. Spray on a full wet coat, but avoid running or dripping. Let it set for 15
minutes if surface was enamel, or 5 minutes if surface was lacquer.
2. Apply a second coat over the first and permit to set for another 15
minutes (enamel surface). For lacquer finishes, move to step 3.
3. Remove the stripped finish using a plastic spreader or other suitable
tool. Re-spray surface with stripper and wash, using steel wool and
water to final clean the surface. Wash from the bottom up on each panel.
Use water only, as soap may leave a residue or film.
POR-15 Paint Remover/Stripper will NOT damage the following:
Glass, Duct Tape, Wood, Glue, Veneer, Rubber*, Leather**, Brass, Steel, Plaster
Walls, Wicker, Aluminum, Factory Fiberglass.
POR-15 Paint Remover/Stripper Will DAMAGE or remove the following:
Tile, Linoleum, Asphalt, Plastics, Synthetics, Sheet Rock, Paper Wicker, Bondo
& other body fillers, when Stripping..Imron, apply two full coats, waiting 10
minutes between coats.GM Black Primer, remove topcoat first, then spray one
full coat, wait 5-10 minutes, then wash with #2 steel wool and water.
Baked Enamel, spray one full wet coat, wait 10 minutes and spray a second
coat over the fi rst without removing any paint. Wait 10 minutes and remove
with scraper. Lacquer, spray a full wet coat, wait 5-10 minutes and lacquer will
melt off. Use plastic scraper to remove.
Polyurethane, spray a full wet coat, wait 20 minutes and remove. POR-15 Paint
Remover/Stripper must be neutralized with a water rinse on metal after
stripped paint has been removed...will not raise the grain on stripped wood...is
not harmed by freezing...will remove mild surface rust...does not contain lye or
acid.
When stripping wood: wash off stripper with wood alcohol, denatured alcohol,
or methanol.
Shelf Life is up to 6 months in an unopened bottle, but it is recommended
that product be used as soon as possible after purchase.
* If rubber soaks in stripper for an hour or more it may temporarily lose its shape; however, if
subsequently washed with water and permitted to dry it will return to original shape.
** Stripper will remove natural oils from leather, but these can easily be replaced with leather
lubricants, tung oil, saddle soap, hide food or other similar products.
CAUTIONS: Keep away from heat, sparks, or open fl ame. Keep container
closed when not in use. Do not take internally. Contact with flame or hot
surface may produce toxic gases. Use of goggles and gloves is strongly
recommended to avoid skin contact or accidental contact. Store away from
heat and out of direct sunlight. Open can slowly to release pressure. If skin
contact is made, wash immediately with soap and water. Avoid prolonged
breathing of vapors. Use only with adequate ventilation. Persons with known
respiratory or heart ailments should exercise extreme caution when using
Methylene-Chloride based products.
Avoid exposure to fumes or vapors.
KEEP OUT OF THE REACH OF CHILDREN
FIRST AID: If swallowed, call physician, hospital emergency room or poison
control center immediately for instructions on inducing vomiting. DO NOT USE
table salt solution. If possible, give one tablespoon of Ipecac syrup and one
glass of water. Patient should lie down, keep warm, cover eyes to exclude light.
FOR EYE CONTACT: Flush repeatedly with water.
FOR SKIN BURN: Apply petroleum jelly to skin.
| POR-Strip |
POR-Strip Application
Custom Product Sales
