 |  |  |  |
Cleans and degreases in one application without leaving residues, noxious
fumes or flammable solvents.
MARINE CLEAN™ is a complex mixture of organic & inorganic chemicals. It is
non-toxic, biodegradable, water-based, and has no noxious odors nor
chlorinated solvents. It does NOT contain any petroleum products and has NO
flash point. Marine Clean represents a revolutionary breakthrough in cleaners,
degreasers and dispersants.
Use MARINE-CLEAN™ for cleaning and degreasing machinery parts, turbine
blades, diesel engines, compressors, transformers, bulkheads, deck plates,
bilge areas; removal of oily deposits found in closed systems such as air
conditioning, boiler tubes, compressor lines, heat exchangers and coils;
removal of light distillates, mineral oils, heavy grease, degreasing all metal
surfaces, plastics, wood, fiberglass, painted surfaces. Always wear eye
protection and rubber gloves when using Marine Clean.
FEATURES
* Biodegradable aqueous cleaning agent
* Low sudsing
* Broad materials and surface compatibility
* Non-corrosive
* Does not contain petroleum or caustic chemicals
* Non-flammable
Applications
Pre-paint cleaning and degreasing prior to the application of paint or primer to aid
coating adhesion.
Removal of dirt, grease, and soil from components to avoid contamination.
Cosmetic cleaning of components or surfaces after use, disassembly, or for aesthetics.
Pre-plate cleaning prior to plating, welding, anodizing, or similar surface finishing to aid
adhesion of the surface finish.
Pre-bond cleaning prior to the application of an adhesive or sealant to aid in bonding
one surface or component to another.
Hydraulic components and bearings that require a high level of cleanliness due to close
tolerances and other physical parameters.
SHOULD MARINE CLEAN ALWAYS BE DILUTED WITH WATER?
Yes. Marine Clean will actually be more effective if it is diluted at least 1:1 with
water.
DOES TEMPERATURE AFFECT THE CLEANING ACTION?
Yes. A hot solution will work better and faster, so dilute with hot water and store Marine
Clean indoors.
WHAT DILUTION IS MOST EFFECTIVE?
That depends on the job to be done. 1:1 is best for engine cleaning, removing baked-on
oil from cylinder heads, removing gum and varnish from fuel tanks. To clean exterior
surfaces of cars or boats,
Use dilutions beginning at 1 part Marine Clean to 5 parts water up to10 parts water.
Always remember to thoroughly rinse off Marine Clean with water after
completing your cleaning job and thoughly dry.
HOW FAST WILL MARINE CLEAN DO THE JOB?
That also depends on the job. Baked-on oil may take up to 2 hours of soaking before it
can be easily brushed or sponged off; gum and varnish in a gas tank may take 24 hours
or more. HOT water mixed with Marine Clean helps solution works best.
***METAL THAT HAS BEEN CLEANED WITH MARINE CLEAN HAS TO BE TREATED
WITH METAL-READY RUST REMOVER/ PREPRIMER***
BEFORE GAS TANK SEALER OR POR-15 RUST PREVENTIVE PAINT CAN BE USED?
Yes. Marine Clean is a powerful caustic solution that leaves an alkaline finish on metal.
An acid finish takes paint better because it etches the metal and gives it a surface profie
with "tooth" for the topcoat paint to bite into. Our Metal-Ready Rust Remover/Preprimer
is the perfect prep to use on any surface that's been cleaned with Marine Clean first.
WHAT ARE OTHER USES FOR MARINE CLEAN?
Cleaning and degreasing of machinery parts, turbine blades, diesel engine compressors,
transformers, bulkheads, deck plates, bilge areas; removal of oily deposits found in
closed systems such as: air conditioning, boiler tubes, compressor lines, heat exchangers
and coils; removal of light distillates, mineral oils, heavy grease, degreasing all metal
surfaces, plastics, wood, fiberglass, painted surfaces. Remember to thoroughly rinse off
Marine Clean with water after completing your cleaning job.
ALWAYS WEAR EYE PROTECTION AND RUBBER GLOVES WHEN USING MARINE
CLEAN.**
